[Issue]: Sending Jobs To Printer And It Just Hangs

by ADMIN 51 views

Issue: Sending Jobs to Printer and it Just Hangs

Sending jobs to a 3D printer can be a frustrating experience, especially when it just hangs without any progress. This issue can be caused by a variety of factors, including printer firmware, mod versions, and screen types. In this article, we will explore the possible causes of this issue and provide troubleshooting steps to help you resolve the problem.

The printer model in question is the Adventurer 5M, with a firmware version of 3.1.5. The mod version is 1.3.1, and the user has installed the Klipper mod earlier.

Screen Type and Other Mods Installed

The user is using the stock screen and has installed the Klipper mod earlier. However, they have not installed the ZMod or ForgeX mods.

What Did You Do?

The user was only able to get this to work once when sending a job to the printer. They have included a screen record of what they are seeing, which can be accessed through the provided link.

What Didn't Work?

When the user sends the code to the printer, it just sits there without any progress. The extruder and bed heat do not turn on, indicating that the printer is not receiving the job correctly.

Debugging Information

The user has provided debugging information in the form of a tar.gz file, which can be accessed through the provided link.

Installation/Uninstallation Logs (if Applicable)

There is no response from the user regarding installation or uninstallation logs.

Checklist

The user has checked the following:

  • They have read the documentation and did not find an answer.
  • They have read the F.A.Q.
  • They have tried rebooting the printer, and the problem persists.

Additional Information

There is no additional information provided by the user.

Based on the information provided, there are several possible causes of the issue:

  • Firmware Version: The firmware version of 3.1.5 may be causing the issue. It is possible that there is a bug in the firmware that is preventing the printer from receiving the job correctly.
  • Mod Version: The mod version of 1.3.1 may also be causing the issue. It is possible that there is a conflict between the mod and the firmware that is preventing the printer from receiving the job correctly.
  • Screen Type: The user is using the stock screen, which may be causing the issue. It is possible that the stock screen is not compatible with the firmware or mod version.
  • Klipper Mod: The user has installed the Klipper mod earlier, which may be causing the issue. It is possible that there is a conflict between the Klipper mod and the firmware or mod version.

To troubleshoot the issue, the user can try the following steps:

  • Update Firmware: The user can try updating the firmware to the latest version to see if it resolves the issue.
  • Update Mod: The user can try updating the mod to the latest version to see if it resolves the issue.
  • Change Type: The user can try changing the screen type to a different one to see if it resolves the issue.
  • Disable Klipper Mod: The user can try disabling the Klipper mod to see if it resolves the issue.

Sending jobs to a 3D printer can be a frustrating experience, especially when it just hangs without any progress. By identifying the possible causes of the issue and following the troubleshooting steps, the user can try to resolve the problem. If the issue persists, it may be necessary to seek further assistance from a 3D printing expert.

Based on the information provided, the following recommendations can be made:

  • Update Firmware: The user should try updating the firmware to the latest version to see if it resolves the issue.
  • Update Mod: The user should try updating the mod to the latest version to see if it resolves the issue.
  • Change Screen Type: The user should try changing the screen type to a different one to see if it resolves the issue.
  • Disable Klipper Mod: The user should try disabling the Klipper mod to see if it resolves the issue.

By following these recommendations, the user can try to resolve the issue and get their 3D printer up and running again.
Q&A: Sending Jobs to Printer and it Just Hangs

In our previous article, we explored the possible causes of the issue where sending jobs to a 3D printer just hangs without any progress. We also provided troubleshooting steps to help you resolve the problem. In this article, we will answer some frequently asked questions related to this issue.

Q: What are the possible causes of the issue?

A: The possible causes of the issue include:

  • Firmware version: The firmware version of 3.1.5 may be causing the issue. It is possible that there is a bug in the firmware that is preventing the printer from receiving the job correctly.
  • Mod version: The mod version of 1.3.1 may also be causing the issue. It is possible that there is a conflict between the mod and the firmware that is preventing the printer from receiving the job correctly.
  • Screen type: The user is using the stock screen, which may be causing the issue. It is possible that the stock screen is not compatible with the firmware or mod version.
  • Klipper mod: The user has installed the Klipper mod earlier, which may be causing the issue. It is possible that there is a conflict between the Klipper mod and the firmware or mod version.

Q: How can I update the firmware?

A: To update the firmware, you can follow these steps:

  1. Download the latest firmware version from the manufacturer's website.
  2. Connect your printer to a computer using a USB cable.
  3. Open the firmware update software and follow the instructions to update the firmware.
  4. Once the update is complete, restart your printer.

Q: How can I update the mod?

A: To update the mod, you can follow these steps:

  1. Download the latest mod version from the manufacturer's website.
  2. Connect your printer to a computer using a USB cable.
  3. Open the mod update software and follow the instructions to update the mod.
  4. Once the update is complete, restart your printer.

Q: How can I change the screen type?

A: To change the screen type, you can follow these steps:

  1. Purchase a new screen that is compatible with your printer.
  2. Disconnect the old screen from your printer.
  3. Connect the new screen to your printer.
  4. Restart your printer.

Q: How can I disable the Klipper mod?

A: To disable the Klipper mod, you can follow these steps:

  1. Open the mod settings on your printer.
  2. Locate the Klipper mod and click on it.
  3. Click on the "Disable" button to disable the mod.
  4. Restart your printer.

Q: What if I still have issues after trying the troubleshooting steps?

A: If you still have issues after trying the troubleshooting steps, it may be necessary to seek further assistance from a 3D printing expert. They can help you diagnose the issue and provide additional troubleshooting steps.

Sending jobs to a 3D printer can be a frustrating experience, especially when it just hangs without any progress. By understanding the possible causes of the issue and following the troubleshooting steps, you can try to resolve the problem. the issue persists, it may be necessary to seek further assistance from a 3D printing expert.

Based on the information provided, the following recommendations can be made:

  • Update firmware: The user should try updating the firmware to the latest version to see if it resolves the issue.
  • Update mod: The user should try updating the mod to the latest version to see if it resolves the issue.
  • Change screen type: The user should try changing the screen type to a different one to see if it resolves the issue.
  • Disable Klipper mod: The user should try disabling the Klipper mod to see if it resolves the issue.

By following these recommendations, the user can try to resolve the issue and get their 3D printer up and running again.